UPVC Window Repairs

uPVC windows are energy efficient and can help reduce heating costs. As they get older, however, issues may develop that need to be fixed. This could be due to damaged hinges, handles, or locks.

Wooden window repair can be relatively straightforward for DIY enthusiasts to complete themselves. It's cheaper than buying a new window repair.

Cracks

Cracks and fractures can pose a serious problem. Windows that are not repaired can lead to water intrusion and weaker barriers to cold weather, or even structural damage. It is crucial to find an experienced local builder or repair service that specialises in the repair of uPVC frames and has the experience, skills and equipment required to achieve the best results. This will ensure that your shattered window is repaired before it gets any worse and you don't have to replace the window glass or window unit.

There are a variety of home solutions that can be utilized to repair small cracks in the glass. Super glue and masking tape are among the most popular products that can hold broken glass in place for a few minutes. For more severe cracks, the tape may need to extend beyond the crack on both sides for optimal results.

Another option is two-part epoxy that can be used to fix broken or cracked glass. This is available from most hardware stores and is available at a cost of around $10. Make sure that your workspace is ready before mixing the epoxy. Also, make sure you have all the equipment necessary for the job.

If you notice that your lower or upper sash isn't lifting it is most likely due to the cords connected to the sashweights are damaged. Thankfully, this is a simple repair that can be made with the help of a ladder and a flathead screwdriver. A damaged dripcap can be easily replaced at home. Drain caps that are free of rot are available at a majority of home centers and can be secured with nails and put in place using caulk. Check that the glass of double or triple-paned window isn't cracked. The reason is because the gasses in the space between the windows are responsible for improving the efficiency of the window and should not escape.

Water Leaks

If your uPVC windows are leaking, it could damage the interior of your home and cause costly repairs. Water leaks can also affect the structure of your home and can cause mold growth. It is crucial to address any issues caused by leaky windows immediately to prevent the damage.

A damaged sealant around window frames is a frequent cause of leaks. The use of silicone caulking can bring the condition of the seal back to normal and prevent water leakage. Look for gaps and cracks around the window frame, as well as the brick or stone wall surrounding your windows.

A blocked drainage hole or an issue with Flashing are two other typical causes of windows that leak. It's crucial to make sure the drainage holes are clean and free of obstruction, particularly during heavy rainstorms. It is also important to look at the windows' flashing to ensure that it is well-sealed.

Finally, it's essential to make sure that your drip cap isn't broken or decaying. A rotten or damaged drip cap could allow water to enter the window from above and cause damage to your home's structure. Replacing drip caps isn't a complicated job and usually a straightforward process of buying an entirely new one and nailing it into place.

A professional can also check your windows for watertightness. They can use a special tool to measure the water-tightness of your windows to make sure they are in line with industry standards. If your windows don't pass the test, you'll have to replace them. This is a costly repair, but it's worth it for the comfort and safety of your family.

Sagging

If your windows aren't closing properly it can cause many issues, such as drafts condensation, and an increase in energy bills. It could also indicate that the windows weren't installed correctly or the sealant has worn away. There are a few options you can try to solve the problem.

The first step is to set up an area that has plenty of light to help repair your window in a timely manner. Start by laying newspaper or an old blanket on the floor to shield it from any splinters or drips that may come from the window while you work.

Use a white cloth that has been soaked in a mixture of detergent and water. This will ensure that you don't leave any stains of color on your windows. When you're ready to start working on your uPVC windows, begin by making note of the location where the hinge channel needs to be located. Then remove the channel from the frame and fill the screw holes using epoxy (for uPVC windows) or wood filler (if frames are made of wood). Be sure to smooth the filled hole before it sets.

Reinstall the hinge channel after the holes have been filled. Make sure it is aligned with the window jamb and make sure you drill the holes for the new screws about quarter inch away from the original locations.

Then, take a measurement of the length of the spindle protruding from underside of the handle and then order a replacement on the internet or Window Repair bring the old one to an hardware store to get a matching. Remove the setscrew off the operator shaft. Smooth it down to allow the set screw to be locked onto the shaft. Now your uPVC window should be closing smoothly.

Broken Hinges

You will have difficulty opening or closing your uPVC windows when the hinges are damaged or aren't working correctly. This could be a security problem and could also hinder your home from staying warm or cold. You can easily purchase a new hinge for your uPVC window. However, it's important to make sure you have the right type of hinge for your windows.

The hinges have to be the same size to fit inside the frame of the window. The most popular type of hinge used in uPVC windows is a standard 15mm or 18mm UPVC window hinge. However, there are specialised types of window hinges for other types of frames such as wooden frames. Choosing the correct window hinge for your windows will assist you in avoiding the typical issues that homeowners encounter with their windows, such as not closing properly.

There are several reasons why your window hinges could have become slack or stiff. The hinges might not be tightened enough. To check this, use a screwdriver to locate the friction screw at the end of the hinge. Release it. Then, you can adjust it by turning it either way.

Call Preston Glass Fix if your UPVC window's hinges don't work properly. We can provide an immediate solution. Our experts will assess the condition of your hinges and offer you advice on the most suitable solution. We can repair or replace the window hinges, re-tension them or install new locking mechanisms to ensure that your UPVC windows are safe and secure for years to come.

The locks are not working properly

UPVC window mechanisms and locks are a crucial component of security for your home. They make it extremely difficult to open a window without breaking into the home. When a lock fails it can be a frustrating experience, but it is a quick and easy repair and you don't need to replace the whole window.

Most of the time, it's a minor issue which could have been averted by regular maintenance. We suggest having your uPVC window serviced regularly as part of our yearly maintenance package in order to minimize the chance of having any issues.

The majority of modern uPVC windows have espagnolette locks which operate by pushing the handle's nose across a wedge block, then turning the handle to close the lock. They are effective at locking the window, however when they are not maintained correctly, over time they can begin to fail. We recommend applying WD-40 to them a few times per year.

If you notice that your uPVC windows aren't opening or shut as easily as they used to, or when the lock isn't functioning properly, it is likely that there is an issue with the locking gearbox within the window frame. It can be difficult to access as it requires removing the seals that surround the window repair near me frame and taking off the handle.

A locksmith who specialises in UPVC repairs has the knowledge to diagnose this fault quickly and then be able to replace the gearbox that failed to lock with a exact replacement. This is a quick and simple repair that can save you hundreds of pounds by not having to purchase new windows.