How to Replace a Kia Sportage replacement key kia soul (https://tempaste.com/YeApURIS4wl) Key

The key of a lot of kia optima keys locked in car models has a keyless entry system built in. This key is similar to an remote control and can be exchanged by an Kia dealer.

Key fobs can stop working for several reasons, including an empty coin battery worn buttons water damage, signal interference and a damaged receiver module. Here are some suggestions to assist you in getting your Kia sportage replacement key working again.

How do you replace the remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, regardless of whether it's a remote as well as a push-to start key or a normal metal key that doesn't contain transponder. This is particularly true if your car displays a message telling you that the smart or remote keys aren't powered.

Luckily, this is an easy procedure. To replace the battery on the key fob remove the mechanical key from the hole in the back of the key fob. You then need to lift the cover. A small screw is found inside the key fob to hold the battery in the correct position. Remove the old battery by unscrewing the screw with the help of a small screwdriver. Then insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock according to your expectations, then you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming done. This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of metal) are not required for programming. If you need to reprogramme your key, you'll need to record the key code number on the tag for the key code.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it is most likely that the battery is insufficient. A low battery may cause other issues, such as the check engine light turning on or the engine not working properly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires just a few basic tools.

Make sure you turn off your vehicle and close all doors prior to starting. Find the small, metal or plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key is released. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new battery so that the "+" positive side faces you and the "-" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts made of metal.

After the new battery has been installed after which you turn the key fob off and then turn it on in the ignition until the door locks. You can then test the Kia's Key fob again to make sure it's working as intended.

How can you replace the smart key?

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs have a battery that will eventually require changing. This is a straightforward process that takes less than two minutes.

Make sure to shut off your Kia and stand on a level well-lit and well-lit area before you begin. Keep in mind that there are small parts inside the fob which could fall out if not careful.

The small release button is located on the lower backside. It could be a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is the CR-2032, and it can be purchased on the internet or at your local auto parts shop. When you are done with the battery, you should be able to lock, unlock and start your vehicle with your key fob - even if your engine isn't running!

How to replace a mechanical key

The Kia key fob is a fantastic convenience that lets us lock and unlock our car with the press of one button. But like any device, it can have problems at times. There are solutions to solve these issues and keep your key fobs functioning for an extended period of time.

One of the most frequent issues is a low or dead battery. This can cause your fob to stop working or operate intermittently. If this is the case, try replacing the battery with a fresh new one.

If this isn't enough to resolve the problem you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the fob to make sure it's working as intended. If the fob still isn't functioning, contact an authorized locksmith or dealer to solve the problem. To avoid locking outs in the future, ensure you purchase an emergency key that will work on all door and trunk cylinders.